Click here to watch the video more »

Cause Toner Density Low (C-2451 - Yellow, C-2542 Magenta, C-2453 - Cyan, C-2454 Black) Resolution Power the machine OFF from the main switch leaving the sub switch ON. Turn main power switch ON while pressing the Utility/Counter key. Keep holding it… more »

From the Adjustments button at the bottom of the screen... Select Quality Adustment Select 02 Density Balace Auto Adj. Select the Output Chart button to print out the chart and then follow the steps on screen more »

All lightweight paper should be long grain stock. All heavy weight stock should be short grain stock. 450x640 indicates Long Grain - shorter number first is long grain 640x450 indicates Short Grain more »

Cause Colour regustration sensor C-4522 Resolution Step 1. Step 2. Power the machine OFF from the main switch leaving the sub switch ON. Turn main power switch ON while pressing the Utility/Counter key. Keep holding it till the comes up in Service mode.… more »

Increase developer conveyance speed at low speed [Service mode]→[System Setting]→[Software DIPSW Setting] Change the DipSW 104-4 from 0 (Normal) to 1 (Increase speed). Change DipSW 104-7 (Defalt). It is to prevent excessive toner supply and ejection.… more »

Cause Can not connect the Command Workstation to the RIP Resolution Power off the printer by opening the front door and turn off the main switch. Power off Fiery RIP by holding the green light button on the RIP. Leave both off for 5 minutes, power the… more »

If you are getting jamming or your paper is coming out of the printer damaged check the separation claws as per the image, they can get a build up of toner underneath you can scrape it off with your finger. Otherwise these will be sitting up on the… more »

C-2811 Yellow C-2812 Magenta C-2813 Cyan C-2814 Black Cause The proper value cannot be figured out within the specified time by the correction of the patch density correction/Y. Alternatively, the proper value of the developing DC output is 0 or lower.… more »

Choose Paper Tray you are printing from Go to Process Adjust or Expert Adjust Set as per image... more »

Adding tape to the blower on the opposite side to the envelope flap can help with skewing, see image... more »

Reset the count for the dust proof filters. Power the machine OFF from the main switch leaving the sub switch ON. Turn main power switch ON while pressing the Utility/Counter key. Keep holding it till the comes up in Service mode. 04 - Counter / Data 03… more »

Step 1. Step 2. Power the machine OFF from the main switch leaving the sub switch ON. Turn main power switch ON while pressing the Utility/Counter key. Keep holding it till the comes up in Service mode. -02 process adjustment -02 drum peculiarity -06… more »

Power the machine OFF from the main switch leaving the sub switch ON. Turn main power switch ON while pressing the Utility/Counter key. Keep holding it till the comes up in Service mode. 04 - Counter / Data 03 - Parts Counter 01 - Special Parts 05 -… more »

Power the machine OFF from the main switch leaving the sub switch ON. Turn main power switch ON while pressing the Utility/Counter key. Keep holding it till the comes up in Service mode. 04 - Counter / Data 03 - Parts Counter 01 - Special Parts 03 -… more »

Remove Side Covers Remove Lid https://youtu.be/Br_4GoHcGhA more »

See images of holding plate and the two screws to remove to take the plate off. more »

Cause If the RIP is stuck on AA or FF and on the printer screen the "Controller Button" is greyed out and in the bottom left hand corner it says "Controller Unconnected" Resolution You will need a USB drive capacity must be 8GB… more »

To increase or decrease the machine stabilization settings... Select the Utility key Administrator settings (01) System Settings (05) Expert Settings (07) Quality Settings (04) Stabilization settings For improved colour consistency increase the maximum… more »

From utilities Select Administrator (01) System Settings (05) Expert Adjustment (07) Quality Adjustment (04) Stabilization Adj. Setting more »

Repeating on envelopes Power the machine OFF from the main switch leaving the sub switch ON. Turn main power switch ON while pressing the Utility/Counter key. Keep holding it till the comes up in Service mode. Set the DIPSW Press 03 System Settings… more »

Click on the file below for instructions. Screen Fix more »

Click on the file below for instructions... Solid Fix more »